onur
1ea2bc64ac
The power mux's status output had no pull-up, which broke the USB current budget interlock. TPS2121 ST is an open-drain output; the datasheet lists RST = 6-20 kOhm under Recommended Operating Conditions, alongside RILM, so it is an external part. ST is driven low only while IN2 (the J3 external 5 V header) is sourcing OUT, and is high impedance whenever IN1 (the J7 USB-C input) is sourcing. U10 gate 2 inverts MUX_ST into EXT_SELECTED, and MAIN_EN = USB_3A_OK OR EXT_SELECTED enables the 15 A core buck. With MUX_ST floating on USB-C power, a drift low asserts MAIN_EN no matter what the TUSB320 advertised, so the board would try to bring up the core rail on a 500 mA port. Every other open-drain net here already has its pull-up (R7/R8, R30, R33/R34, R98/R104/R105/R106); this one was missed. R108 (10 k, VCC3V3_AUX -> MUX_ST) is appended at the end of design_data.py rather than beside the mux: reference designators are assigned in call order, so inserting it mid-file would renumber every later resistor and invalidate the routed board. Placed at (53.0, 101.6), 2.4 mm from the U10 gate it holds up, on a site checked clear of existing copper, and routed with close_remaining.py. Also corrects POWER_TREE.md, which credited PR1 for giving the external input priority. PR1 = GND actually *disables* priority mode; CP2 (tied to VCC3V3_AUX) is what selects IN2. Since CP2 derives from the mux's own output the behaviour is two-phase - highest-voltage wins at cold start, IN2 unconditionally once the aux rail is up - so with both inputs connected there can be one seamless switchover at startup. Documented, with the numbers: both eFuses UV 3.98 V / OV 5.80 V, ILIM 2.69 A (USB-C) and 4.04 A (header), mux OV 5.69 V / ILIM 4.5 A. The two inputs are never summed: both eFuses block reverse current and the mux bonds exactly one input at a time. board_routed.kicad_sch/.kicad_sym are now gitignored byte copies of the tracked schematic; kicad-cli needs them beside the board for --schematic-parity, and deleting them in the previous commit had silently disabled that check. Verified: ERC 0/0, DRC 0 violations, 0 unconnected, every net one copper group, schematic parity unchanged at the 402 pre-existing warnings. Co-Authored-By: Claude Opus 5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_012KaTmCCxCEW4awsmXRNT1d
Çıktılar
Bu klasör build/routing çalışma alanıdır. Repository'de yalnızca güncel ve anlamlı teslim çıktıları tutulur:
bom.csv: ayrıntılı mühendislik BOM'u.jlcpcb_bom.csv: montaj servisi için sadeleştirilmiş BOM.erc_final_reset.rpt: güncel şema ERC raporu; 0 ihlal.drc_final_placement.rpt: unrouted placement DRC raporu.drc_power_local.rpt: sinyal routing'inden önceki güç katı DRC raporu.drc_final_routed.rpt: routed kart DRC raporu.board_final_reset_top.png: güncel üst görünüm.
Routing çalışma dosyaları:
signal_stage.dsn/signal_stage.ses: autorouter'a verilen ve ondan alınan sinyal katı. Sadeceboard_power_local.kicad_pcbile birlikte anlamlıdır.signal_stage_preview.kicad_pcb: DSN'e giren bakırın KiCad'de incelenebilir hâli.freerouting_signal.log: pass başına unrouted/violation sayısı.
Eski .dsn, .ses, preview PCB ve ara DRC raporları yeni netlist için
authoritative değildir. .dsn her zaman onu üreten karta bağlıdır: placement,
güç bakırı veya keepout değiştiğinde export ve routing baştan yapılmalıdır,
yoksa import edilen sonuç mevcut bakırla çakışır.
Final routed raporda sıfır açık bağlantı, sıfır clearance/short ve sıfır
schematic-parity hatası hedeflenir. Unrouted aşamadaki unconnected_items,
via_dangling ve isolated_copper kayıtları normaldir: sırasıyla henüz
çekilmemiş bağlantıları, henüz kullanılmayan BGA escape via'larını ve final
fill'de silinecek plane parçalarını gösterir.