onur
1ea2bc64ac
The power mux's status output had no pull-up, which broke the USB current budget interlock. TPS2121 ST is an open-drain output; the datasheet lists RST = 6-20 kOhm under Recommended Operating Conditions, alongside RILM, so it is an external part. ST is driven low only while IN2 (the J3 external 5 V header) is sourcing OUT, and is high impedance whenever IN1 (the J7 USB-C input) is sourcing. U10 gate 2 inverts MUX_ST into EXT_SELECTED, and MAIN_EN = USB_3A_OK OR EXT_SELECTED enables the 15 A core buck. With MUX_ST floating on USB-C power, a drift low asserts MAIN_EN no matter what the TUSB320 advertised, so the board would try to bring up the core rail on a 500 mA port. Every other open-drain net here already has its pull-up (R7/R8, R30, R33/R34, R98/R104/R105/R106); this one was missed. R108 (10 k, VCC3V3_AUX -> MUX_ST) is appended at the end of design_data.py rather than beside the mux: reference designators are assigned in call order, so inserting it mid-file would renumber every later resistor and invalidate the routed board. Placed at (53.0, 101.6), 2.4 mm from the U10 gate it holds up, on a site checked clear of existing copper, and routed with close_remaining.py. Also corrects POWER_TREE.md, which credited PR1 for giving the external input priority. PR1 = GND actually *disables* priority mode; CP2 (tied to VCC3V3_AUX) is what selects IN2. Since CP2 derives from the mux's own output the behaviour is two-phase - highest-voltage wins at cold start, IN2 unconditionally once the aux rail is up - so with both inputs connected there can be one seamless switchover at startup. Documented, with the numbers: both eFuses UV 3.98 V / OV 5.80 V, ILIM 2.69 A (USB-C) and 4.04 A (header), mux OV 5.69 V / ILIM 4.5 A. The two inputs are never summed: both eFuses block reverse current and the mux bonds exactly one input at a time. board_routed.kicad_sch/.kicad_sym are now gitignored byte copies of the tracked schematic; kicad-cli needs them beside the board for --schematic-parity, and deleting them in the previous commit had silently disabled that check. Verified: ERC 0/0, DRC 0 violations, 0 unconnected, every net one copper group, schematic parity unchanged at the 402 pre-existing warnings. Co-Authored-By: Claude Opus 5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_012KaTmCCxCEW4awsmXRNT1d
22 lines
751 B
Plaintext
22 lines
751 B
Plaintext
Board: hardware/board_routed.kicad_pcb
|
|
Unconnected endpoints reported by connectivity: 0
|
|
Tracks: 3068 Vias: 1020
|
|
|
|
Track segments per layer:
|
|
F.Cu 1748
|
|
L6_SIG 482
|
|
L5_SIG 390
|
|
L3_SIG 387
|
|
B.Cu 61
|
|
|
|
Track width used per net class (mm: segments):
|
|
BGA_ESCAPE 0.1: 423
|
|
CLOCK 0.1: 17, 0.15: 145
|
|
Default 0.1: 37, 0.12: 1375, 0.15: 5
|
|
POWER 0.1: 79, 0.12: 4, 0.15: 193, 0.163: 18, 0.195: 1, 0.2: 4, 0.22: 12, 0.227: 3, 0.25: 248, 0.26: 6, 0.3: 327, 0.35: 1, 0.4: 103, 0.45: 2, 0.5: 2, 0.55: 10, 0.6: 4, 0.7: 2, 0.8: 5, 1.0: 1, 1.2: 4, 1.5: 2
|
|
RF50_CPWG 0.164: 11
|
|
USB90_DIFF 0.135: 24
|
|
|
|
Nets still split into more than one copper group:
|
|
none - every net is one connected group
|